Til innhold
NORSK
SØK
Tilbake til konsernsiden
0
Forespørsel

Dimensjoner

  • Lengde(mm):
    2991
  • Bredde(mm):
    2438
  • Høyde(mm):
    2896
  • Vekt (kg):
    13000
  • Løfting/ Transport:
    10’ Offshore ISO container with forklift pockets and lifting slings. DNV 2.7-1 Can be stacked in height with use of ISO locks.

Byggeår

  • Byggeår:
    2013
  • Oppgradert/ombygd (år):
    2018

Bruksområde / Sertifisering

  • Onshore/offshore:

    Offshore

  • Standard:
    Offshore, Zone II, Norsok Z-015, ATEX II 3G IIA T3
  • Drift (Elektrisk/Diesel):

    Diesel

Flow / Trykk / Volum

  • Hz v Q-maks måling:
    N/A (Diesel)
  • Q-max (l/min):
    3600
  • Hz v P-maks måling:
    N/A (Diesel)
  • P-max (bar):
    525
  • Flowrate1:
    3602 ltr/min @ 113 bar (6" Plunger@7. gear, 2100 RPM)
  • Flowrate2:
    2035 ltr/min @ 201 bar (6" Plunger@4. gear, 2100 RPM)
  • Flowrate3:
    961 ltr/min @ 425bar (6" Plunger@1. gear, 2100 RPM)
  • Diesel tankvolum (ltr):
    1200
  • Dieselforbruk (ltr/time):
    280

Tilkoblinger

  • Tilkopling inn:
    6” 150 Ansi via integrated feed pump or external feeder minimum 3.5 bar at full flow on triplex pump
  • Tilkopling ut:
    2 ea. 3" Fig 1502 Female.

Pumpe(r)

  • Pumpe1 (type):
    Gardner Denver GD-2250 Triplex pump . Standard Plunger 6", other sizes on request.

Motor(er)

  • Motor1 (type):
    MUST BE CONNECTED TO SEPERATE MOTOR UNIT (PP-74A)

Strømforsyning

  • (A):
    10-16

Annen informasjon

  • Utstyr / Funksjoner:

    MUST BE CONNECTED TO SEPERATE MOTOR UNIT (PP-74A), (see separate datasheets for technical information)

    Two-piece unit, where the engine and pump has to be connected via a drive shaft, hydraulic and diesel hoses (Diesel tank is located at pump unit).

    Diesel level must be limited to 600 liters for offshore use.

    Hydraulically integrated feed pump.

    LIMITATIONS:

    - 80% load is 960 HHP@ 2100 rpm, can be used for 50% of the duty cycle or 6 out of every 12 hours.

    - 70% load is 840 HHP @ 2100 rpm. Operation below this can be used cyclic continuous.

    - 100% load is 1150 HHP @ 2100 rpm, Can be used for maximum one hour. The following hour has to be below

    - 70% (840 HHP @ 2100 rpm)

    If the speed is lowered to 1800 rpm, the full load is lowered to 1040 HHP.

    - 80% load is 830 HHP@ 1800 rpm.

    - 70% load is 730 HHP @ 1800 rpm.

    - If these limits are exceeded there will be limited warrant.

    For further information please contact Maintenance Diesel Department.